The questions we hear most, with more to come at launch.
Don’t see your question? contact@studio3e8.com
The Mesa 1 is a metal 3D printer that fits on your desk and plugs into a standard wall outlet. It prints and sinters parts in one machine, with no gas supply or external sintering furnace.
Copper and carbon steel will be our first metals, available at launch.
The Mesa 1 builds parts by depositing powders from sealed cartridges, in layers at room temperature. Each layer is completely filled - metal powder where the part is, and scaffold material everywhere else. The scaffold holds the metal powder in place, so no support structures are needed. Precisely tuned vibration allows the powder to flow through the nozzle like a fluid, and the boundary between metal and scaffold defines the part’s shape.
After printing, the entire powder bed is heated right inside of the printer where it was laid down. The metal particles bond (sinter) together into a solid part, and the scaffold material stays loose. Once the cooling phase is complete, the finished part lifts easily out of the scaffold material.
We call this process Scaffold Contrast Sintering (SCS).
No. The Mesa 1 uses no binders and no laser - only sealed cartridges of metal and scaffold powder and an integrated sintering furnace. The metal is held in its shape by the scaffold without binders to join it or lasers to melt it.
No. The Mesa 1 prints and sinters in one integrated machine, without requiring a gas supply or gas generator.
Existing sinter-based metal printers use a separate furnace that relies on process gases or a vacuum to address the challenge of oxidation, which hurts the strength and density of sintered parts. When metal is heated, it reacts with oxygen in the air to form an oxide layer on its surface that prevents particles from bonding. The established solution is to use reactive gases to remove those oxides or to put the furnace in a vacuum chamber to prevent them from forming, both of which add cost and complexity.
To avoid this cost and complexity, the Mesa 1 uses an internal crucible seal and specialized chemistry that removes oxygen from around the part during sintering, so there’s no gas supply to connect and no bulky vacuum chamber required.
The Mesa 1 has three crucible options, which can print finished parts of the following maximum sizes:
Smaller crucibles print smaller parts faster and use less scaffold. Parts shrink evenly and predictably as they sinter, and our software scales your part up automatically to compensate.
Most prints take 24 to 48 hours, including sintering. The largest parts can take up to 72 hours for the entire cycle.
Our slicer runs on your computer and supports STL, STEP, OBJ, 3MF, and Parasolid (.x_t) files. Import a part, slice it, and send it to the printer in as few as three clicks, with no supports or build plate. The software also accounts for shrinkage during sintering; there are no scale factors to calculate by hand.
The Mesa 1 was designed around the safety concerns of other metal 3D printing methods. It uses no binders or lasers, its materials come in fully sealed cartridges, and it sinters parts in a built-in furnace with no external gas required.
Laser-based printers (DMLS) often involve handling loose metal powder, especially when separating the finished part from the unused powder around it. The laser also vaporizes a small amount of metal, which condenses into fine reactive particles that collect inside the machine and its filter, requiring careful handling and sometimes special disposal.
Binder-based processes, such as binder jetting and metal filament, remove their binders with solvents or by burning them off, which can release harmful volatiles. Their sintering furnaces need vacuum chambers or process gases, including flammable gases like hydrogen.
The Mesa 1 uses no laser, so it produces none of these particles. It has no binders to remove and requires no vacuum or process gas.
No. Metal powder comes in fully sealed cartridges, and all of it ends up in the finished part, so there is no unused metal powder to clean up or dispose of. The scaffold around the part stays loose, and the part is simply lifted out after sintering.
The furnace was designed from the ground up for safe operation. It uses high-quality components like metallurgical-grade heating elements and platinum-type thermocouples, with redundant temperature sensing inside and outside the furnace. Custom control electronics and firmware provide fault detection across hardware, firmware, and software. The printer door and furnace lid lock automatically during operation.
A failed print automatically goes through an accelerated sintering cycle that turns the loose metal powder into a solid piece, which can then be safely disposed of.
Like any kiln or furnace, the Mesa 1 should be vented outdoors or through an air filtration system using the included exhaust port.
Before shipping, the Mesa 1 will be UL and CE certified, so we can deliver to backers in the US, Canada, and Europe. All materials will include Safety Data Sheets.